HELLO! BOOT0 is starting!
boot0 version : 1.2.1
dram size =512
Succeed in opening nand flash.
Succeed in reading Boot1 file head.
The size of Boot1 is 0x00036000.
The file stored in 0X00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[ 0.116] boot1 version : 1.2.5
[ 0.117] pmu type = 3
[ 0.144] axi:ahb:apb=3:2:2
[ 0.144] set dcdc2=1400, clock=1008 successed
[ 0.146] key
[ 0.159] no key found
[ 0.159] flash init start
[ 0.787] flash init finish
[ 0.788] fs init ok
[ 0.789] fs mount ok
[ 0.793] script finish
[ 0.795] power finish
[ 0.799] BootMain start
[ 0.799] 13
[ 0.812] gpio config
[ 0.812] gpio ok
[ 0.812] gpio finish
[ 0.815] The all optional count is 1
[ 0.818] recovery config
[ 0.823] test for multi os boot with display
[ 0.825] show pic finish
[ 0.828] load kernel start
[ 0.848] load kernel successed
[ 0.848] start address = 0x4a000000
U-Boot 2011.09-rc1-00000-g0283ea7-dirty (Feb 10 2012 - 18:08:25) Allwinner Technology
CPU: SUNXI Family
Board: A10-EVB
DRAM: 512 MiB
NAND: 3800 MiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:9-
-name- -start- -size-
BOOTFS : 100000 1000000
LROOTFS : 1100000 2000000
LSYSTEMFS : 3100000 10000000
LDATAFS : 13100000 60000000
MISC : 73100000 100000
LRECOVERYFS : 73200000 2000000
LCACHEFS : 75200000 8000000
env : 7d200000 200000
UDISK : 7d400000 70400000
-----------------------------------
Hit any key to stop autoboot: 0
sun4i#
sun4i#
sun4i#
sun4i#
sun4i#
sun4i#
sun4i#
sun4i#
sun4i#help
? - alias for 'help'
base - print or set address offset
boot - boot default, i.e., run 'bootcmd'
boota - boota - boot android bootimg from memory
bootd - boot default, i.e., run 'bootcmd'
bootm - boot application image from memory
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
env - environment handling commands
exit - exit script
false - do nothing, unsuccessfully
fastboot- fastboot- use USB Fastboot protocol
fatdown - download data to a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
go - start application at address 'addr'
help - print command description/usage
key_test- Test the key value and dump key registers
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nm - memory modify (constant address)
printenv- print environment variables
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
showvar - print local hushshell variables
test - minimal test like /bin/sh
true - do nothing, successfully
version - print monitor, compiler and linker version
sun4i#run runsd
Device: SUNXI SD/MMC
Manufacturer ID: 1b
OEM: 534d
Name: SD
Tran Speed: 25000000
Rd Block Len: 512
SD version 1.10
High Capacity: No
Capacity: 1.9 GiB
Bus Width: 4-bit
reading uImage
3400084 bytes read
## Booting kernel from Legacy Image at 50000000 ...
Image Name: Linux-2.6.36-android
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3400020 Bytes = 3.2 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Linux version 2.6.36-android (matt@ubuntu10) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #11 PREEMPT Mon Feb 13 09:11:54 CST 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: sun4i
[ 0.000000] Lichee System fixup
[ 0.000000] Total Detected Memory: 512MB with 1 banks
[ 0.000000] Memory Reserved:
[ 0.000000] VE: 0x43000000, 0x04a00000
[ 0.000000] FB: 0x5a000000, 0x02000000
[ 0.000000] G2D: 0x58000000, 0x01000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 114688
[ 0.000000] free_area_init_node: node 0, pgdat c06abba0, node_mem_map c0767000
[ 0.000000] DMA zone: 896 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 113792 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rw rootfstype=ext4 init=/init loglevel=8 rootwait mac_addr=00:CE:39:B6:5D:B4
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 448MB = 448MB total
[ 0.000000] Memory: 322252k/322252k available, 136500k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfee00000 - 0xffe00000 ( 16 MB)
[ 0.000000] vmalloc : 0xdc800000 - 0xf0000000 ( 312 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002e000 ( 152 kB)
[ 0.000000] .text : 0xc002e000 - 0xc0675000 (6428 kB)
[ 0.000000] .data : 0xc0676000 - 0xc06ac7a0 ( 218 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:96
[ 0.000000] timer_set_mode: periodic
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1005.97 BogoMIPS (lpj=5029888)
[ 0.240000] pid_max: default: 32768 minimum: 301
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] devtmpfs: initialized
[ 0.250000] DRAM Size: 512
[ 0.250000] regulator: core version 0.5
[ 0.250000] NET: Registered protocol family 16
[ 0.250000] No ATAGs?
[ 0.250000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 0.250000] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
[ 0.250000] bio: create slab <bio-0> at 0
[ 0.250000] SCSI subsystem initialized
[ 0.250000] libata version 3.00 loaded.
[ 0.250000] usbcore: registered new interface driver usbfs
[ 0.250000] usbcore: registered new interface driver hub
[ 0.250000] usbcore: registered new device driver usb
[ 0.260000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.260000] Bluetooth: Core ver 2.15
[ 0.260000] NET: Registered protocol family 31
[ 0.260000] Bluetooth: HCI device and connection manager initialized
[ 0.260000] Bluetooth: HCI socket layer initialized
[ 0.260000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.260000] Init eGon pin module V2.0
[ 0.260000] Switching to clocksource aw 64bits couter
[ 0.260000] NET: Registered protocol family 2
[ 0.260000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.260000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.260000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.260000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.260000] TCP reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] NET: Registered protocol family 1
[ 0.270000] RPC: Registered udp transport module.
[ 0.270000] RPC: Registered tcp transport module.
[ 0.270000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.270000] sw_sys: init
[ 0.270000] [pm]aw_pm_init!
[ 0.270000] ashmem: initialized
[ 0.280000] NTFS driver 2.1.29 [Flags: R/W].
[ 0.280000] fuse init (API version 7.15)
[ 0.280000] msgmni has been set to 629
[ 0.280000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.280000] io scheduler noop registered
[ 0.280000] io scheduler deadline registered
[ 0.280000] io scheduler cfq registered (default)
[ 0.290000] G2D: drv_g2d_init
[ 0.290000] G2D: g2dmem: g2d_start=58000000, g2d_size=1000000
[ 0.290000] G2D: head:d8000000,tail:d9000000
[ 0.290000] G2D: Module initialized.major:251
[ 0.290000] sw-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a sw-uart0
[ 0.300000] console [ttyS0] enabled
[ 0.310000] sw-uart.2: ttyS2 at MMIO 0x1c28800 (irq = 3) is a sw-uart2
[ 0.310000] brd: module loaded
[ 0.320000] loop: module loaded
[ 0.320000] [NAND]nand driver, init.
[ 0.330000] [NAND] nand gpio_request
[ 0.330000] [NAND] nand driver version: 0x2 0x6
[ 0.340000] nand interrupte register ok
[ 0.340000] ret of NFC_ChangMode is 0
[ 0.340000] dma_hdle is 0
[ 0.350000] dma_hdle is 10000008
[ 0.370000] PHY_PageReadSpare : too much ecc err,bank 0 block 0,page ff
[ 0.380000] PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 0
[ 1.030000] The 0 disk name = BOOTFS, class name = DISK, disk size = 32768
[ 1.040000] The 1 disk name = LROOTFS, class name = DISK, disk size = 65536
[ 1.050000] The 2 disk name = LSYSTEMFS, class name = DISK, disk size = 524288
[ 1.050000] The 3 disk name = LDATAFS, class name = DISK, disk size = 3145728
[ 1.060000] The 4 disk name = MISC, class name = DISK, disk size = 2048
[ 1.070000] The 5 disk name = LRECOVERYFS, class name = DISK, disk size = 65536
[ 1.080000] The 6 disk name = LCACHEFS, class name = DISK, disk size = 262144
[ 1.090000] The 7 disk name = env, class name = DISK, disk size = 4096
[ 1.090000] The 8 disk name = UDISK, class name = DISK, disk size = 0
[ 1.100000] The 8 disk size = 3678208
[ 1.100000] part total count = 9
[ 1.110000] nanda:
[ 1.110000] nandb: unknown partition table
[ 1.220000] nandc: unknown partition table
[ 1.330000] nandd: unknown partition table
[ 1.330000] nande: unknown partition table
[ 1.340000] nandf: unknown partition table
[ 1.440000] nandg: unknown partition table
[ 1.550000] nandh: unknown partition table
[ 1.560000] nandi:
[ 1.560000] [NAND]nand driver, ok.
[ 1.560000] sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
[ 1.570000] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
[ 1.580000] sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.590000] sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
[ 1.590000] scsi0 : sw_ahci_platform
[ 1.600000] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 56
[ 1.610000] PPP generic driver version 2.4.2
[ 1.610000] PPP Deflate Compression module registered
[ 1.620000] PPP BSD Compression module registered
[ 1.620000] PPP MPPE Compression module registered
[ 1.630000] NET: Registered protocol family 24
[ 1.630000] wemac Ethernet Driver, V1.00 in file:drivers/net/sun4i/sun4i_wemac.c
[ 1.640000] [EMAC] ahb clk enable
[ 1.650000] [EMAC] ahb gate clk: 0x2026140
[ 1.660000] wemac wemac.0: PHY SETUP, reg 0 value: 3100
[ 1.670000] wemac wemac.0: resetting device
[ 1.670000] release temp resource
[ 1.680000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.690000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.690000] [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc06ea768
[ 1.700000] [sw-ehci1]: open clock
[ 1.720000] [sw-ehci1]: Set USB Power ON
[ 1.730000] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.740000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 1
[ 1.750000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
[ 1.770000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
[ 1.770000] ehci_irq: port change detect
[ 1.780000] hub 1-0:1.0: USB hub found
[ 1.780000] hub 1-0:1.0: 1 port detected
[ 1.780000] [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc06ea878
[ 1.790000] [sw-ohci1]: open clock
[ 1.820000] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.830000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 2
[ 1.830000] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
[ 1.900000] hub 2-0:1.0: USB hub found
[ 1.900000] hub 2-0:1.0: 1 port detected
[ 1.910000] [sw-ehci2]: probe, pdev->name: sw-ehci, pdev->id: 2, sw_ehci: 0xc06ea98c
[ 1.920000] [sw-ehci2]: open clock
[ 1.940000] [sw-ehci2]: Set USB Power ON
[ 1.950000] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.950000] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 3
[ 1.960000] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
[ 1.990000] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
[ 1.990000] ehci_irq: port change detect
[ 2.000000] hub 3-0:1.0: USB hub found
[ 2.000000] hub 3-0:1.0: 1 port detected
[ 2.000000] [sw-ehci2]: sw_usb_disable_ehci
[ 2.010000] [sw-ehci2]: remove, pdev->name: sw-ehci, pdev->id: 2, sw_ehci: 0xc06ea98c
[ 2.020000] sw-ehci sw-ehci.2: remove, state 1
[ 2.020000] usb usb3: USB disconnect, address 1
[ 2.030000] sw-ehci sw-ehci.2: USB bus 3 deregistered
[ 2.040000] [sw-ehci2]: Set USB Power OFF
[ 2.040000] [sw-ehci2]: close clock
[ 2.040000] [sw-ohci2]: probe, pdev->name: sw-ohci, pdev->id: 2, sw_ohci: 0xc06eaa9c
[ 2.050000] [sw-ohci2]: open clock
[ 2.080000] [sw-ohci2]: Set USB Power ON
[ 2.080000] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 2.090000] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 3
[ 2.100000] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
[ 2.110000] usb 1-1: new high speed USB device using sw-ehci and address 2
[ 2.160000] hub 3-0:1.0: USB hub found
[ 2.160000] hub 3-0:1.0: 1 port detected
[ 2.170000] [sw-ohci2]: sw_usb_disable_ohci
[ 2.170000] [sw-ohci2]: remove, pdev->name: sw-ohci, pdev->id: 2, sw_ohci: 0xc06eaa9c
[ 2.180000] sw-ohci sw-ohci.2: remove, state 1
[ 2.190000] usb usb3: USB disconnect, address 1
[ 2.190000] sw-ohci sw-ohci.2: USB bus 3 deregistered
[ 2.200000] [sw-ohci2]: Set USB Power OFF
[ 2.200000] [sw-ohci2]: close clock
[ 2.210000] Initializing USB Mass Storage driver...
[ 2.210000] usbcore: registered new interface driver usb-storage
[ 2.220000] USB Mass Storage support registered.
[ 2.220000] usbcore: registered new interface driver usbserial
[ 2.230000] USB Serial support registered for generic
[ 2.270000] hub 1-1:1.0: USB hub found
[ 2.270000] hub 1-1:1.0: 4 ports detected
[ 2.280000] usbcore: registered new interface driver usbserial_generic
[ 2.290000] usbserial: USB Serial Driver core
[ 2.290000] USB Serial support registered for GSM modem (1-port)
[ 2.300000] usbcore: registered new interface driver option
[ 2.300000] option: v0.7.2:USB Driver for GSM modems
[ 2.310000] WRN:L158(drivers/usb/sun4i_usb/manager/usb_manager.c):ERR: get usbc(0) id failed
[ 2.320000] WRN:L164(drivers/usb/sun4i_usb/manager/usb_manager.c):ERR: get usbc(0) det_vbus failed
[ 2.330000] WRN:L158(drivers/usb/sun4i_usb/manager/usb_manager.c):ERR: get usbc(1) id failed
[ 2.340000] WRN:L164(drivers/usb/sun4i_usb/manager/usb_manager.c):ERR: get usbc(1) det_vbus failed
[ 2.350000] WRN:L158(drivers/usb/sun4i_usb/manager/usb_manager.c):ERR: get usbc(2) id failed
[ 2.360000] WRN:L164(drivers/usb/sun4i_usb/manager/usb_manager.c):ERR: get usbc(2) det_vbus failed
[ 2.370000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.400000] android init
[ 2.400000] android-platform_device_register
[ 2.400000] ------print_msc_config-----
[ 2.410000] vendor_id = 0x18d1
[ 2.410000] mass_storage_id = 0x1
[ 2.420000] adb_id = 0x2
[ 2.420000] usb_manufacturer_name = USB Developer
[ 2.430000] ata1.00: ATA-7: ST3160815AS, 4.AAB, max UDMA/133
[ 2.430000] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.440000] usb_product_name = Android
[ 2.440000] usb_serial_number = 20080411
[ 2.450000] msc_vendor_name = USB 2.0
[ 2.450000] msc_product_name = USB Flash Driver
[ 2.460000] msc_release = 100
[ 2.460000] luns = 3
[ 2.470000] ---------------------------
[ 2.470000] android_probe pdata: c0693da4
[ 2.480000] android_bind
[ 2.480000] android_bind_config
[ 2.480000] Gadget Android: controller 'sw_usb_udc' not recognized
[ 2.490000] android_usb gadget: android_usb ready
[ 2.500000] ata1.00: configured for UDMA/133
[ 2.500000] [ps2]: sw_ps2_init
[ 2.500000] ps2: cannot find any unsing configuration for 2 ps/2 controller, return directly!
[ 2.510000] mice: PS/2 mouse device common for all mice
[ 2.520000] scsi 0:0:0:0: Direct-Access ATA ST3160815AS 4.AA PQ: 0 ANSI: 5
[ 2.530000] sun4i RTC version 0.1
[ 2.530000] sun4i-rtc sun4i-rtc: f23_rtc_probe tmp_data = 380239881
[ 2.540000] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 2.550000] sd 0:0:0:0: [sda] Write Protect is off
[ 2.560000] using rtc device, rtc, for alarms
[ 2.560000] sun4i-rtc sun4i-rtc: rtc core: registered rtc as rtc0
[ 2.570000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.570000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.580000] i2c /dev entries driver
[ 2.590000] ================power===================, status = 0
[ 2.590000] gsensor_i2c_awxx_init: script_parser_fetch gsensor_name err, err = -4
[ 2.600000] ctp_used == 0.
[ 2.610000] sda: sda1
[ 2.610000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.620000] bus num = 0, twi used = 1
[ 2.620000] bus num = 1, twi used = 1
[ 2.620000] bus num = 2, twi used = 1
[ 2.630000] config i2c gpio with gpio_config api
[ 2.630000] twi0, apb clock = 24000000
[ 2.640000] _twi_set_clk: clk_n = 0, clk_m = 5
[ 2.640000] axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected
[ 2.650000] I2C: i2c-0: AW16XX I2C adapter
[ 2.660000] **********start************
[ 2.660000] 0x40
[ 2.660000] 0xf8
[ 2.660000] 0x28
[ 2.670000] 0x0
[ 2.670000] 0x0
[ 2.670000] **********end************
[ 2.670000] twi1, apb clock = 24000000
[ 2.680000] _twi_set_clk: clk_n = 0, clk_m = 11
[ 2.680000] I2C: i2c-1: AW16XX I2C adapter
[ 2.690000] **********start************
[ 2.690000] 0x40
[ 2.700000] 0xf8
[ 2.700000] 0x58
[ 2.700000] 0x0
[ 2.700000] 0x0
[ 2.700000] **********end************
[ 2.710000] twi2, apb clock = 24000000
[ 2.710000] _twi_set_clk: clk_n = 0, clk_m = 11
[ 2.720000] I2C: i2c-2: AW16XX I2C adapter
[ 2.720000] **********start************
[ 2.730000] 0x40
[ 2.730000] 0xf8
[ 2.730000] 0x58
[ 2.730000] 0x0
[ 2.730000] 0x0
[ 2.740000] **********end************
[ 2.740000] lirc_dev: IR Remote Control driver registered, major 250
[ 2.750000] IR NEC protocol handler initialized
[ 2.750000] IR RC5(x) protocol handler initialized
[ 2.760000] IR RC6 protocol handler initialized
[ 2.760000] IR JVC protocol handler initialized
[ 2.770000] IR Sony protocol handler initialized
[ 2.770000] IR LIRC bridge handler initialized
[ 2.780000] Linux video capture interface: v2.00
[ 2.780000] [cedar dev]: install start!!!
[ 2.790000] [cedar dev]: install end!!!
[ 2.790000] [ace_drv] init end!!!
[ 2.800000] [pa_drv] start!!!
[ 2.800000] [pa_drv] init end!!!
[ 2.800000] regulator: axp20_ldo1: 1300 mV
[ 2.810000] regulator: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[ 2.820000] regulator: axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[ 2.830000] regulator: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[ 2.830000] regulator: axp20_buck2: 700 <--> 2275 mV at 1400 mV
[ 2.840000] regulator: axp20_buck3: 700 <--> 3500 mV at 1250 mV
[ 2.850000] regulator: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[ 2.850000] input: axp20-supplyer as /devices/platform/aw16xx-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
[ 2.870000] device-mapper: uevent: version 1.0.3
[ 2.880000] device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@redhat.com
[ 2.890000] device-mapper: multipath: version 1.1.1 loaded
[ 2.890000] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.900000] Bluetooth: HCI UART driver ver 2.2
[ 2.900000] Bluetooth: HCI H4 protocol initialized
[ 2.910000] Bluetooth: HCI BCSP protocol initialized
[ 2.910000] Bluetooth: HCILL protocol initialized
[ 2.920000] [mmc_pm]: no sdio card used in configuration
[ 2.930000] [mmc]: awsmc_init
[ 2.930000] [mmc]: awsmc controller unsing config sdc0 1, sdc1 1, sdc2 0, sdc3 1
[ 2.940000] [mmc]: awsmc.0: pdev->name: awsmc, pdev->id: 00000000
[ 2.950000] [mmc]: smc 0, source = sdram_pll_p, src_clk = 360000000, mclk 40000000,
[ 2.950000] [mmc]: MMC Driver init host 0
[ 2.960000] [mmc]: sdc 0 idma des address d9ac4000
[ 2.960000] [mmc]: mmc 0 suspend pins
[ 2.970000] [mmc]: awsmc.0: Initialisation Done. ret 0
[ 2.970000] [mmc]: awsmc.1: pdev->name: awsmc, pdev->id: 00000001
[ 2.980000] [mmc]: smc 1, source = sdram_pll_p, src_clk = 360000000, mclk 40000000,
[ 2.990000] [mmc]: MMC Driver init host 1
[ 2.990000] [mmc]: sdc 1 idma des address d9ac8000
[ 3.000000] [mmc]: mmc 1 suspend pins
[ 3.000000] [mmc]: awsmc.1: Initialisation Done. ret 0
[ 3.010000] [mmc]: awsmc.3: pdev->name: awsmc, pdev->id: 00000003
[ 3.020000] [mmc_pm]: No sdio card, please check your config !!
[ 3.020000] [mmc_pm]: No sdio card, please check your config !!
[ 3.030000] [mmc]: smc 3, source = sdram_pll_p, src_clk = 360000000, mclk 90000000,
[ 3.040000] [mmc]: MMC Driver init host 3
[ 3.040000] [mmc]: sdc 3 idma des address d9acc000
[ 3.050000] [mmc]: mmc 3 suspend pins
[ 3.050000] [mmc]: awsmc.3: Initialisation Done. ret 0
[ 3.060000] usbcore: registered new interface driver usbhid
[ 3.060000] usbhid: USB HID core driver
[ 3.070000] logger: created 64K log 'log_main'
[ 3.070000] logger: created 256K log 'log_events'
[ 3.080000] logger: created 64K log 'log_radio'
[ 3.080000] logger: created 64K log 'log_system'
[ 3.090000] enter sun4i Audio codec!!!
[ 3.100000] sun4i audio support initialized
[ 3.100000] baseaddr = dc85ec00
[ 3.100000] audiocodec_adap_awxx_init: script_parser_fetch err.
[ 3.110000] sun4i Audio codec successfully loaded..
[ 3.120000] No device for DAI sun4i-hdmiaudio
[ 3.120000] No device for DAI SNDHDMI
[ 3.130000] asoc: SNDHDMI <-> sun4i-hdmiaudio mapping ok
[ 3.130000] No device for DAI sun4i-spdif
[ 3.140000] No device for DAI SNDSPDIF
[ 3.140000] asoc: SNDSPDIF <-> sun4i-spdif mapping ok
[ 3.150000] ALSA device list:
[ 3.150000] #0: sun4i-CODEC Audio Codec
[ 3.160000] #1: SUN4I_SNDHDMI (SNDHDMI)
[ 3.160000] #2: SUN4I_SNDSPDIF (SNDSPDIF)
[ 3.160000] nf_conntrack version 0.5.0 (5035 buckets, 20140 max)
[ 3.170000] IPv4 over IPv4 tunneling driver
[ 3.180000] GRE over IPv4 tunneling driver
[ 3.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.190000] TCP cubic registered
[ 3.190000] NET: Registered protocol family 10
[ 3.200000] IPv6 over IPv4 tunneling driver
[ 3.200000] NET: Registered protocol family 17
[ 3.210000] NET: Registered protocol family 15
[ 3.210000] Bluetooth: L2CAP ver 2.15
[ 3.220000] Bluetooth: L2CAP socket layer initialized
[ 3.220000] Bluetooth: SCO (Voice Link) ver 0.6
[ 3.230000] Bluetooth: SCO socket layer initialized
[ 3.230000] Bluetooth: RFCOMM TTY layer initialized
[ 3.240000] Bluetooth: RFCOMM socket layer initialized
[ 3.240000] Bluetooth: RFCOMM ver 1.11
[ 3.250000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.250000] Bluetooth: BNEP filters: protocol multicast
[ 3.260000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.270000] lib80211: common routines for IEEE802.11 drivers
[ 3.270000] lib80211_crypt: registered algorithm 'NULL'
[ 3.280000] [mmc_pm]: No sdio card, please check your config !!
[ 3.290000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 3.310000] regulator_init_complete: incomplete constraints, leaving axp20_buck3 on
[ 3.310000] regulator_init_complete: incomplete constraints, leaving axp20_buck2 on
[ 3.330000] regulator_init_complete: incomplete constraints, leaving axp20_ldo4 on
[ 3.330000] regulator_init_complete: incomplete constraints, leaving axp20_ldo3 on
[ 3.350000] regulator_init_complete: incomplete constraints, leaving axp20_ldo2 on
[ 3.350000] regulator_init_complete: incomplete constraints, leaving axp20_ldo1 on
[ 3.370000] sun4i-rtc sun4i-rtc: f23_rtc_gettime
[ 3.370000] sun4i-rtc sun4i-rtc: read time 2010-1-1 0:0:9
[ 3.390000] sun4i-rtc sun4i-rtc: setting system clock to 2010-01-01 00:00:09 UTC (1262304009)
[ 3.490000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.500000] VFS: Mounted root (ext4 filesystem) on device 8:1.
[ 3.530000] devtmpfs: mounted
[ 3.540000] Freeing init memory: 152K
[ 3.540000] Failed to execute /init. Attempting defaults...
[ 3.970000] [mmc]: mmc 0 detect change, present 1
modprobe: FATAL: Could not load /lib/modules/2.6.36-android/modules.dep: No such file or directory
init: ureadahead main process (65) terminated with status 5
[ 4.070000] [mmc]: mmc 0 resume pins
[ 4.110000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 52, RTO !!
[ 4.120000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 52, RTO !!
[ 4.130000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 8, RTO !!
[ 4.140000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 5, RTO !!
[ 4.150000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 5, RTO !!
[ 4.160000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 5, RTO !!
[ 4.160000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 5, RTO !!
[ 4.190000] [mmc]: sdxc_request_done(L973): smc 0 err, cmd 8, RTO !!
[ 4.240000] mmc0: new high speed SD card at address b368
[ 4.240000] mmcblk0: mmc0:b368 SD 1.90 GiB
[ 4.250000] mmcblk0: p1 p2
init: procps main process (96) terminated with status 255
Ubuntu 10.04 LTS sun4i ttyS0
sun4i login: root
Password:
Login incorrect
sun4i login: ubuntu
Password:
Linux sun4i 2.6.36-android #11 PREEMPT Mon Feb 13 09:11:54 CST 2012 armv7l GNU/Linux
Ubuntu 10.04 LTS
Welcome to Ubuntu!
* Documentation: https://help.ubuntu.com/
The programs included with the Ubuntu system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by
applicable law.
To run a command as administrator (user "root"), use "sudo <command>".
See "man sudo_root" for details.
ubuntu@sun4i:~$
ubuntu@sun4i:~$ cd /lib/modules/
ubuntu@sun4i:/lib/modules$ ls
2.6.36-android
ubuntu@sun4i:/lib/modules$ cd 2.6.36-android/
ubuntu@sun4i:/lib/modules/2.6.36-android$ ls
8192cu.ko hv2605.ko mt9m113.ko sw_ahci_platform.ko
ar6000.ko iwmc3200top.ko mxc622x.ko swbb23_dhd.ko
asix.ko iwmc3200wifi.ko nano_if.ko swbb23_fw.bin
ath6k lcd.ko nano_ksdio.ko swbb23_nvram.txt
ath.ko lib ov2655.ko ump.ko
bma250.ko libahci.ko ov7670.ko unifi_sdio.ko
dhd.ko libertas.ko qf9700.ko usbnet.ko
disp.ko libertas_tf.ko rtl8150.ko usi4329_dhd.ko
example.ko mali.ko scsi_wait_scan.ko usi4329_fw.bin
ft5x_ts.ko mcs7830.ko sp0838.ko usi4329_nvram.txt
gc0308.ko mecs.ko sun4i_csi0.ko videobuf-core.ko
goodix_touch.ko mma7660.ko sun4i_csi1.ko videobuf-dma-contig.ko
gspca_main.ko modules.builtin sun4i-ir.ko x_mac.axf
gt2005.ko modules.order sun4i-keyboard.ko zt8031.ko
hdmi.ko Module.symvers sun4i-ts.ko
hi704.ko mt9m112.ko sun4i-vibrator.ko
ubuntu@sun4i:/lib/modules/2.6.36-android$ lsmod
Module Size Used by
hdmi 14119 0
lcd 2559 0
disp 201888 2 hdmi,lcd
ubuntu@sun4i:/lib/modules/2.6.36-android$ ifconfig
warning: no inet socket available: No such file or directory
lo Link encap:Local Loopback
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ubuntu@sun4i:/lib/modules/2.6.36-android$ ifconfig eth0 192.168.1.244
No support for INET on this system.
ubuntu@sun4i:/lib/modules/2.6.36-android$